Kenworth W900 Detroit Diesel Parts

AC Compressor - Pad Top Mount Base - Cat/Detroit 8 Groove

$385.00

AC Compressor Clutch - 8 Groove Serpentine

$160.00

AC High Pressure NC Switch

$45.00

AC Plumbing - Kenworth or Peterbilt - Discharge Line

$445.00

An air intake piping kit for a Kenworth or Peterbilt truck with external, side of cab mounted air cleaner when installing a Caterpillar C12 engine, Cummins ISX CM570 or Detroit Diesel Series 60 DDEC3, DDEC4 or DDEC5 engine.

Air Intake Adapter Piping Kit - Kenworth or Peterbilt - Cummins ISX CM570 - Detroit DDEC3/4/5 - Cat C12 - External Breather(s)

$195.00

An air intake piping kit for a Kenworth or Peterbilt truck with external, side of cab mounted air cleaner.

Air Intake Adapter Piping Kit - Y Pipe to 90 Degree Elbow

$195.00

A universal 90-degree LONG RADIUS air intake elbow. Each side of the elbow accepts a 6" OD tube.

Air Intake Elbow - 90 Degree - 6" - Long Radius

$139.00

A universal 90-degree short radius air intake elbow, 6" x 6" OD Tube

Air Intake Elbow - 90 Degree - 6" - Short Radius

$34.00

A 90-degree air intake elbow, this is a reducing elbow, 6" x 5" OD tube.

Air Intake Elbow - 90 Degree Reducing - 6" x 5"

$34.00

A universal air intake straight hump hose. Each side of the hump hose accepts a 6" OD tube.

Air Intake Hump Hose - Straight - 6"

$34.00

Alternator - Presto Lite Pad Mount 170 Amp

$350.00

Battery Cable Kit - Extended Length

$795.00

Battery Cable Kit - Standard Length

$535.00

Battery Hold Down Kit - Kenworth Cantilever Box

$495.00

Battery Hold Down Kit - Kenworth Step Box Battery Box

$310.00

Belt Set - 10/8 Groove Serpentine - Top Mount - 15.75" Fan Center Height

$110.00

A Detroit Diesel Series 60 Air Intake Manifold

CAC Air Intake Manifold - Detroit DDEC3/4 - Kenworth or Peterbilt

$2,995.00

Carrier Bearing Plate

$105.00

An air to air hose used to connect the left or right side charge air cooler tube to the engine and the charge air cooler.

Charge Air Cooler Hump Hose - Black

$40.00

A stainless steel constant torque clamp typically used to clamp an intake boot to the pipe. For use on 6" diameter intake systems.

Clamp - Constant Torque - 6" Stainless Steel

$16.00

Clutch Micro Switch

$40.00

Coolant Distribution Manifold - 3 Port - Bare Block

$545.00

Kustom Truck 3-port coolant distribution manifold kit

Coolant Distribution Manifold - 3 Port - With Fittings

$1,195.00

Coolant Distribution Manifold - 5 Port - Bare Block

$695.00

Kustom Truck 5-port coolant distribution manifold kit

Coolant Distribution Manifold - 5 Port - With Fittings

$1,780.00

Cooling Module Ground Harness - Kenworth or Peterbilt

$115.00

Cross Member Kit - Kenworth

$1,175.00

Genuine Detroit Diesel Series 60 vertical thermostat housing and seal kit to attach to the engine block on DDEC3 or DDEC4 engine electronics.

Detroit DDEC3/4 Thermostat Housing and Seal Kit - Vertical Outlet

$435.00

Detroit Front Engine Upfit - 10/8 Groove Serpentine Kit - Fits Kenworth W900 or Peterbilt 388/389

$1,815.00

Detroit Front Engine Upfit - Accessory Drive Kit

$1,125.00

An installation kit to plumb the fuel lines from the splitter valves to a Detroit engine with composite hose and compression fittings.

Detroit Fuel Line Plumbing Kit - Compression Fittings & Composite Hose

$330.00

Kit to plumb the fuel lines from the splitter valves to a Detroit Diesel Series 60 engine with nitrile braided hose and JIC fittings.

Detroit Fuel Line Plumbing Kit - JIC Fittings & Nitrile Braided Hose

$595.00

A generic engine control harness to install a Detroit Diesel Series 60 engine with DDEC3 or DDEC4 electronics, cab to engine ecm harness.

Detroit Legacy Engine Harness - S60 DDEC3 or DDEC4 Harness

$3,650.00

A toggle switch, dash label and sensor kit for the dash of a heavy duty truck

Detroit Legacy Engine Harness - S60 DDEC3, DDEC4 and DDEC5 - Switch, Sensor and Label Kit

$750.00

A generic engine control harness to install a Detroit Diesel Series 60 engine with DDEC5 electronics, cab to engine ecm harness.

Detroit Legacy Engine Harness - S60 DDEC5 Harness

$3,650.00

Detroit Water Pump Coolant Fitting Kit for the Pump to Coolant Reservoir

$145.00

Exhaust Kit - Dynaflex - Peterbilt/Kenworth

$3,950.00

Exhaust Kit - Lincoln Chrome - Peterbilt/Kenworth

$3,950.00

Exhaust Piping - Level 1 - Below Frame

$600.00

Fan Blade - 30" Diameter - 9 Blades - 2.5" Pilot

$235.00

A 30 inch diameter, 9 blade fan with a 5 inch pilot diameter

Fan Blade - 30" Diameter - 9 Blades - 5" Pilot

$290.00

Fan Blade - 32" Diameter - 11 Blades - 2.5" Pilot

$275.00

A 32" diameter, 9 blade engine cooling fan

Fan Blade - 32" Diameter - 9 Blades - 2.5" Pilot

$235.00

Fan Blade - 32" Diameter - 9 Blades - 5" Pilot

$322.00

Fan Hub - Detroit Series 60 - 2 Speed 10 Groove Serpentine - DM Advantage

$2,290.00

Fan Hub - Detroit Series 60 - 2 Speed Triple V Belt - DM Advantage

$2,320.00

Fan Hub - Detroit Series 60 - On/Off 10 Groove Serpentine - DM Advantage

$1,840.00

Fan Hub - Detroit Series 60 - On/Off Triple V Belt - DM Advantage

$1,690.00

A 3 inch stainless steel fan shroud extension ring.

Fan Shroud Extension Ring 3" with Rivets

$450.00

A 7 inch stainless steel fan shroud extension ring

Fan Shroud Extension Ring 7" with Rivets

$550.00

Fan Solenoid - Normally Closed - 2 Speed

$150.00

Fan Solenoid - Normally Closed - On/Off

$150.00

Fan Solenoid - Normally Open - On/Off

$150.00

Detroit Diesel Series 60 Front motor mount for Peterbilt and Kenworth trucks

Front Engine Mount Bracket - Detroit Series 60 - Kenworth or Peterbilt

$1,370.00

Front Engine Mount Bushing Kit - with Hardware

$250.00

Front Trunion Support Bracket Kit with Hardware

$425.00

a fuel filter restriction sensor kit with Compression fitting

Fuel Filter Restriction Kit - Compression Fittings

$495.00

Fuel Filter Restriction Kit - JIC Fittings

$495.00

Air intake manifold Gasket for Detroit Series 60

Gasket Kit - Detroit DDEC3/4/5 CAC Air Intake Housing

$65.00

silicone coolant hose .062 inches diameter x 25 feet long cut length

Heater Hose - Silicone - 5/8" Black - 25 ft Roll

$140.00

Heater Hose Plumbing Kit - Peterbilt Day Cab or All Kenworth Trucks - Black

$285.00

Heater Hose Plumbing Kit - Peterbilt Day Cab or All Kenworth Trucks - Black - For Use With Kustom Coolant Manifold

$495.00

Heater Hose Plumbing Kit - Peterbilt Day Cab or All Kenworth Trucks - Blue

$285.00

J1587 Data Bus Block

$86.00

Jumper Harness - J1587 - Data Bus Block to Firewall Connector

$125.00

Jumper Harness - J1587 - Diagnostic Plug to Data Bus Block

$125.00

Kenworth AC Plumbing - Suction Line

$225.00

An exhaust support bracket kit that is used on Kenworth trucks that have an above the frame exhaust system with a single right side above from exhaust.

Kenworth Bracket Kit - Support Bracket RS Above Frame Single Exhaust

$650.00

Kenworth Charge System Harness - NAMUX3

$280.00

Kenworth Exhaust Piping - Level 1 - Above Frame

$525.00

Kenworth Level 2 Above the frame exhaust piping kit

Kenworth Exhaust Piping - Level 2 - Above Frame

$925.00

Exhaust piping adapter kit to get from the back of turbo to the front of the "Y" Pipe on a Kenworth truck with a below the frame exhaust system.

Kenworth Exhaust Piping - Level 2 - Below Frame

$925.00

Exhaust piping adapter kit to get from the back of turbo to through the "Y" Pipe on a Kenworth truck with a below the frame standard Kenworth exhaust system.

Kenworth Exhaust Piping - Level 3 - Below Frame - For OEM Elbows

$1,425.00

Exhaust piping adapter kit to get from the back of turbo to through the "Y" Pipe on a Kenworth truck with a below the frame Pickett Style exhaust system.

Kenworth Exhaust Piping - Level 3 - Below Frame - For Pickett Elbows

$1,200.00

Kenworth Exhaust Piping - Level 3 - Below Frame - For Single Right Side

$995.00

Engine installation harness for installing a Detroit Series 60 engine (DDEC5 engine electronics) into a Kenworth truck with NAMUX1 chassis electronics and Caterpillar 70 Pin ADEM3 engine electronics.

Kenworth NAMUX1 Harness - Detroit DDEC5 - 1

$2,950.00

Kenworth NAMUX1 Harness - Detroit DDEC5 - 2

$2,950.00

Glider Kit engine installation harness for installing a Detroit Series 60 engine (DDEC3 or DDEC4 engine electronics) into a Kenworth truck with NAMUX3 chassis electronics.

Kenworth NAMUX3 Harness - Detroit DDEC3/4 with Processor

$3,650.00

Glider Kit engine installation harness for installing a Detroit Series 60 engine (DDEC5 engine electronics) into a Kenworth truck with NAMUX3 chassis electronics.

Kenworth NAMUX3 Harness - Detroit DDEC5 with Processor

$3,650.00

A J1587 dash jumper harness that works for both Kenworth or Peterbilt trucks. The J1587 dash jumper includes a 2 piece firewall to bus block and bus block bypass to OBD extension.

Kenworth or Peterbilt Harness - GEN2 J1587 Dash Jumper - 2 Piece Firewall to Bus Block and Bus Block Bypass to OBD

$125.00

A J1587 jumper harness that works for both Kenworth or Peterbilt trucks. The J1587 harness is to be installed when bypassing the bus block to OBD port.

Kenworth or Peterbilt Harness - J1587 Bus Block Bypass to OBD

$125.00

A 2010 and newer Kenworth Power distribution harness kit that supplies power to the chassis and engine.

Kenworth Power Distribution Kit - NAMUX3 - Extended Length

$2,195.00

Kenworth Power Distribution Kit - NAMUX3 - Standard Length

$1,895.00

An installation harness to supply power from the alternator when charging back to the battery positive.

Kenworth Power Feed Harness - NAMUX3

$1,290.00

Kenworth Pre 2011 Engine Mounts - Detroit Series 60

$750.00

Kenworth Pre 2011 Engine Mounts- Frame Side Brackets

$1,075.00

Kenworth Pre-NAMUX Harness - 04 to 05 Detroit DDEC3/4 - 1

$2,950.00

Kenworth Pre-NAMUX Harness - 04 to 05 Detroit DDEC3/4 - 2

$2,750.00

Kenworth Pre-NAMUX Harness - 04 to 05 Detroit DDEC5 - 2

$2,550.00

Kenworth Pre-NAMUX Harness - 94 to 98 Detroit DDEC3/4 - 1

$3,950.00

Engine installation harness for installing a Detroit Series 60 engine (DDEC5 engine electronics) into a Pre-NAMUX 1994-1998 Kenworth truck with Caterpillar 40 Pin ADEM2 chassis electronics.

Kenworth Pre-NAMUX Harness - 94 to 98 Detroit DDEC5 - 1

$3,950.00

Kenworth Pre-NAMUX Harness - 94 to 99 Detroit DDEC3/4 - 3

$3,650.00

Kenworth Pre-NAMUX Harness - 94 to 99 Detroit DDEC5 - 3

$3,650.00

Engine installation harness for installing a Detroit Series 60 engine (DDEC3 or DDEC4 engine electronics) into a Pre-NAMUX 1996-2001 Kenworth truck with Cummins Celect Plus chassis electronics.

Kenworth Pre-NAMUX Harness - 96 to 01 Detroit DDEC3/4 - 2

$3,650.00

Kenworth Pre-NAMUX Harness - 96 to 01 Detroit DDEC5 - 2

$3,650.00

Kenworth Pre-NAMUX Harness - 99 to 03 Detroit DDEC3/4 - 1

$3,950.00